Answer
Typical drip edge measurements are around 2.5″ wide and 1.5″ deep, with the flange that nails to the roof surface being approximately 2.5″ wide and the vertical edge that directs roof runoff down and away being approximately 1.5″ deep. Drip is available in a variety of lengths, but is commonly supplied in ten-foot lengths (120″).
What size does drip edge come in, and what other options are there?
This drip edge profile is in the form of a “T,” with a lower flange at the bottom of the drip edge. Roof drip edges are often offered in lengths of 10.5 feet, however they are sometimes available in lengths as short as 8 feet or even less. The length of the overhang itself is typically between 2 and 5 inches in length.
In addition, do you use drip edge nails or a nail gun?
The drip edge should be fastened to the roof deck using a minimum of 12-gauge roofing nails that are positioned 8 to 10 inches apart and 1-12 to 3 inches away from the edge of the sheathing. Drip edge pieces that are next to one other should be lapped a minimum of 2 inches. The asphalt shingles should have a 14- to 34-inch overhang on the external edge of the drip edge.
Also, how far should the shingles extend beyond the drip edge is important to know.
When installing drip edge flashing, the edge of the shingles should hang over the roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if no drip edge flashing is used. When there is too much overhang, the shingles may be blown off in heavy winds; when there is too little, water can leak into the rake or fascia boards.
What is the best way to increase the pace of the drip edge?
Detail of the roof drip edge flashing corner Install the drip edge along the eaves of the roof, then apply the underlayment before placing the drip edge along the gable end. The ideal method is to put the drip edge solely along the eaves at first, and subsequently to cover the drip edge with ice-and-water barrier (in the snowbelt) or felt paper (underlayment).
There were 30 related questions and answers found.
Is it true that the drip edge goes beneath the tar paper?
The drip edge should be over the paper at the eaves and under the rake over the whole length of the roof. mroberson: It’s a SET-UP! Back in my building days, I learnt that you should position the tar paper on the eaves OVER the drip edge to ensure that any moisture that seeps through the shingles does not reach under the drip edge.
Do rain gutters extend below the drip edge?
It is simple to attach a thin strip of metal flashing beneath the drip edge and over the rear of the gutter, rather than removing and reinstalling your gutter. This will allow the water to shed into the gutter without having to remove and reinstall your gutter.
Should the drip edge be flush with the fascia?
The drip edge should be fitted atop a piece of 12 furring strip to ensure that it is not in direct contact with the fascia or rafter tails during installation. If the drip edge is placed right up against the fascia or rafters, the water will flow straight up against the fascia and beneath the soffit due to the surface tension of the water.
How much does it cost to have a drip edge installed?
Drip Edges cost between $1 and $2 every linear foot of installed length. Water is directed into the gutters by the addition of drip edges to the roofing material. Other Damage — Before replacing your fascia and soffits, have a professional evaluate your eaves for signs of water damage.
Do you need a drip edge when installing metal roofing?
Rainwater is directed away from the fascia and into the gutter by a drip edge, which is typically made of metal (generally aluminium) and extends beyond other portions of the roof and beyond other elements of the roof. This is crucial because a poorly placed drip edge–or no drip edge at all–can cause gutters to overflow, either in the front or the rear.
Is it possible to add drip edge on an existing roof?
In order to replace the drip edge eave strips, follow these steps: Install the eave strips on the lower roof edges first, tucking the eave strips beneath the shingles and felt underlayment to prevent water from getting into the roof. Align one end of the lower eave strip with the edge of the roof decking so that it is flush with it. The eave strip should be secured in place with galvanised roofing nails once the roof shingles have been lifted.
What is causing the water to drop between the gutter and fascia?
This is most likely because the gutter was constructed without any flashing over the rear of the gutter, resulting in water trickling from behind your gutter. The gutter apron will keep the leaking to a minimum. Unbent section of flashing that is hidden beneath the shingles and above the gutter is known as a gutter apron or gutter skirt.
Should shingles be allowed to extend over the drip edge?
Yes. It is recommended that shingles do not extend above the drip edge by more than 3/4″ (19 mm). It is not supported if shingles exceed the edge of the roof by more than 3/4″ (19 mm), at which point they are likely to fracture and break off. In addition, the wind resistance at the roof edge may be reduced as a result of this.
Is it better to have the drip edge go over or beneath felt?
There is just one answer. It is dependent on the location of the drip edge. The drip edge of a roof extends over the roofing felt on the sides, or gables, of the roof. The drip edge is located at the bottom of the roof and is concealed behind the roofing felt.
What is the best way to fasten the drip edge?
Check to ensure that the outside border goes beyond the gutter. Otherwise, slide the drip edge slightly out from beneath the tiles to ensure that it does not clog. Roofing cement should be used to secure the drip edge. Press the shingle down onto the drip edge after applying a continuous bead of cement along its top edge.
How far should the roof sheathing extend beyond the fascia?
It measures 45-3/4 inches in length. Using a tape measure, measure up the rafter 45-3/4 inch from where the truss tail was cut and draw a line along the trusses. There should be enough overhang here to allow for the installation of the fascia and subfascia, which will tuck neatly below the roof sheathing when the time comes.
What colour drip edge should I use? | What should I use?
The most often seen drip edge colours are white and brown. Some roofing providers, on the other hand, may create drip edge that matches the roof colour. Colors are often selected to match the shingles or gutters in order to create a seamless appearance. Also possible is selecting a colour that coordinates with the shutters or trim of the home and serves as an accent colour.
What kind of nails do you use for the drip edge on your rugs?
Galvanized roofing nails, 1-1/2 inch in length, are used to secure the drip edge in place. When it comes to marking cuts, a felt-tip marker is ideal. And, once again, using a thin flat rod to pry out the end of the piece enables the parts to overlap neatly.
Post Views: 3Spread the love
ncG1vNJzZmivp6x7r6%2FEq6upp5mjwW%2BvzqZma2hiZ3xxfo6wn5qsXaGyr7PToWSdp5WoeqW%2ByKlknpyXmnqku8yeZKKmXp3Brrg%3D